Registrován: 05.08.2002
Příspěvků: 898

Koupil jsem to,..
zdá se že by to mohlo umět 108Mb.
Umí to zřejmě reřimy AP, PtP,PtMP,klient

umí to telnetit,..

Na to jsem zatim přišel.
Mno ale mam zajímavý problém, možná jde jen o nějaké chybné nastavení.

Když pustim netstumbler s kartou XI325 tak to apčko najde, ale navzorkuje to jen jednou sílu signálu a pak to už jen hlásí že žádné ap nebylo nalezeno.

Netušíte někdo čím to je ??

Registrován: 05.08.2002
Příspěvků: 898

tohle to vypíše na telnetu:

WLAN Access Point login: admin
Password:

Atheros Access Point Rev 3.0.0.43A
WLAN Access Point wlan1 -> help
List of Access Point CLI commands:
config wlan -- config wlanX
connect bss -- connect to bssX
del acl -- Delete Access Control List
del wdsacl -- Delete WDS Access Control List
del key -- Delete Encryption key
find bss -- Find BSS
find channel -- Find Available Channel
find all -- Find All BSS
superftp -- Software update via FTP
had -- Software update HAD file via FTP
ftp -- Software update TFP file via FTP
get 11gonly -- Display 11g Only Allowed
get 11goptimize -- Display 11g Optimization Level
get 11goverlapbss -- Display Overlapping BSS Protection
get acl -- Display Access Control List
get wdsacl -- Display WDS Access Control List
get wdsap -- Display WDS Access Point
get aging -- Display Aging Interval
get antenna -- Display Antenna Diversity
get association -- Display Association Table
get authentication -- Display Authentication Type
get autochannelselect -- Display Auto Channel Select
get apmode -- Display AP Mode(runtime)
get apmodenext -- Display AP Mode after reboot
get beaconinterval -- Display Beacon Interval
get burstSeqThreshold -- Display Max Number of frames in a Burst
get burstTime -- Display Burst Time
get channel -- Display Radio Channel
get cipher -- Display Encryption cipher
get config -- Display Current AP Configuration
get countrycode -- Display Country Code
get ctsmode -- Display CTS mode
get ctsrate -- Display CTS rate
get ctstype -- Display CTS type
get dhcpc -- Display DHCP Clinet State
get domainsuffix -- Display Domain Name Server suffix
get dtim -- Display Data Beacon Rate (DTIM)
get encryption -- Display Encryption Mode
get extendedchanmode -- Display Extended Channel Mode
get eth2wlan -- Display Eth2Wlan Broadcast packet filter state
get fragmentthreshold -- Display Fragment Threshold
get frequency -- Display Radio Frequency (MHz)
get gateway -- Display Gateway IP Address
get groupkeyupdate -- Display Group Key Update Interval (in Seconds)
get hardware -- Display Hardware Revisions
get hostipaddr -- Display Host IP Address
get ipaddr -- Display IP Address
get ipmask -- Display IP Subnet Mask
get key -- Display Encryption Key
get keyentrymethod -- Display Encyrption Key Entry Method
get keysource -- Display Source Of Encryption Keys
get login -- Display Login User Name
get nameaddr -- Display IP address of name server
get power -- Display Transmit Power Setting
get radiusname -- Display RADIUS server name or IP address
get radiusport -- Display RADIUS port number
get rate -- Display Data Rate
get rtsthreshold -- Display RTS/CTS Threshold
get rootapmac -- Display Root AP MAC Address
get rootapinfo -- Display Root AP Information
get shortpreamble -- Display Short Preamble Usage
get shortslottime -- Display Short Slot Time Usage
get sntpserver -- Display SNTP/NTP Server IP Address
get ssid -- Display Service Set ID
get ssidsuppress -- Display SSID Suppress Mode
get station -- Display Station Status
get SuperG -- Display SuperG Feature Status
get systemname -- Display Access Point System Name
get sta2sta -- Display wireless STAs to wireless STAs connect state
get eth2sta -- Display ethernet to wireless STAs connect
state
get telnet -- Display Telnet Mode
get timeout -- Display Telnet Timeout
get tzone -- Display Time Zone Setting
get uptime -- Display UpTime
get wirelessmode -- Display Wireless LAN Mode
get wlanstate -- Display wlan state
help -- Display CLI Command List
ping -- Ping
reboot -- Reboot Access Point
quit -- Logoff
set 11gonly -- Set 11g Only Allowed
set 11goptimize -- Set 11g Optimization Level
set 11goverlapbss -- Set Overlapping BSS Protection
set acl -- Set Access Control List
set wdsacl -- Set WDS List
set aging -- Set Aging Interval
set antenna -- Set Antenna
set authentication -- Set Authentication Type
set autochannelselect -- Set Auto Channel Selection
set apmode -- Set AP Mode
set beaconinterval -- Modify Beacon Interval
set burstSeqThreshold -- Set Max Number of frames in a Burst
set burstTime -- Set Burst Time
set channel -- Set Radio Channel
set cipher -- Set Cipher
set ctsmode -- Set CTS Mode
set ctsrate -- Set CTS Rate
set ctstype -- Set CTS Type
set dhcpc -- Set DHCP Clinet State
set domainsuffix -- Set Domain Name Server Suffix
set dtim -- Set Data Beacon Rate (DTIM)
set encryption -- Set Encryption Mode
set extendedchanmode -- Set Extended Channel Mode
set eth2wlan -- Set Eth2Wlan Broadcast packet filter state
set factorydefault -- Restore to Default Factory Settings
set fragmentthreshold -- Set Fragment Threshold
set frequency -- Set Radio Frequency (MHz)
set gateway -- Set Gateway IP Address
set groupkeyupdate -- Set Group Key Update Interval (in Seconds)
set hostipaddr -- Set Host IP address
set ipaddr -- Set IP Address
set ipmask -- Set IP Subnet Mask
set key -- Set Encryption Key
set keyentrymethod -- Select Encryption Key Entry Method
set keysource -- Select Source Of Encryption Keys
set login -- Modify Login User Name
set nameaddress -- Set Name Server IP address
set password -- Modify Password
set passphrase -- Modify Passphrase
set power -- Set Transmit Power
set radiusname -- Set RADIUS name or IP address
set radiusport -- Set RADIUS port number
set radiussecret -- Set RADIUS shared secret
set rate -- Set Data Rate
set rootapmac -- Set Root AP MAC Address
set rtsthreshold -- Set RTS/CTS Threshold
set shortpreamble -- Set Short Preamble
set shortslottime -- Set Short Slot Time
set sntpserver -- Set SNTP/NTP Server IP Address
set ssid -- Set Service Set ID
set ssidsuppress -- Set SSID Suppress Mode
set SuperG -- Super G Features
set systemname -- Set Access Point System Name
set sta2sta -- Set wireless STAs to wireless STAs connect state
set eth2sta -- Set ethernet to wireless STAs connect state
set telnet -- Set Telnet Mode
set timeout -- Set Telnet Timeout
set tzone -- Set Time Zone Setting
set wlanstate -- Set wlan state
set wirelessmode -- Set Wireless LAN Mode
timeofday -- Display Current Time of Day
version -- Software version
tftp get -- Get a file from TFTP Server.
tftp uploadtxt -- Upload the configuration of the device to
TFTP Server.
tftp srvip -- Setup the TFTP Server IP address.
tftp update -- Update the file to the device.
tftp info -- Information about the TFTPC setting.

Registrován: 05.08.2002
Příspěvků: 898

sem na to už přišel
je třeba vypnout superG režim, když je zaplej tak to nedovede přepínat na 11Mb

Registrován: 20.07.2004
Příspěvků: 5

Nevite nekdo jak a co vsechno nastavit abych rozjel tento ap v klient modu. nejak se mi to nepodarilo rozjet. musi byt klient za ap v klient modu v jine subsiti?

Registrován: 23.11.2004
Příspěvků: 1

musis tam zadat MAC adresu nadrazenaho AP a mit spravne vyplneny SSID a pripadne nastaveny WEP.

Registrován: 08.09.2002
Příspěvků: 641

Team Member: MOD

a jak je na tom tohle ap s regulaci???

Registrován: 05.08.2002
Příspěvků: 898

prikaz set power....
mno ale nemnel jsem sanci to nejak omerit

jako klient to jede v pohode
pres telnet: find bss nebo find all
chvili nic nedela a pka zacne jednou za 5 sekund vypisovat co to chytilo

pak connect bss

ted si tim nejsem jistej mozna jsem ty prikazy zmotal,....

Registrován: 12.02.2003
Příspěvků: 292

tak tohle je podle vypisu telnetu D-Link DWL 2100AP

__________________